![]() ![]() She had trouble fitting me inside normally, and this was a clone of me at my thickest that had no give to it, so she found it almost useless for penetration but still enjoyed it as a vibrator on her clit and enjoyed what it resembled when I wasn't around for her.Description Ever asked yourself, “How can I clone my willy?” ![]() My girlfriend said that the material was extremely hard. It had captured every little vein and detail of my penis. The result was pretty cool to look at it. We put the vibe in and kind of forgot about it while it was setting, and when we returned to it after it had hardened we found the vibe had shifted and was very slightly pressed against the side, so a small portion of it was exposed on the top of the final clone, probably only 1cm in diameter. Unfortunately, it ended up being about an inch and a half or two inches shorter than it could have been which was a little disappointing but not a dealbreaker. According to the dimensions provided on the website, the mix they sent was supposed to be more than enough. Took a little cocktail of arginine, tribulus, and whatnot, and used a good ring that stayed tight to my base and the whole process of making it with my girlfriend was a turn on so maintaining an erection wasn't a problem. I made one once with a girlfriend a few years back. (Timing isn't important for this step, so long as you put your cock in the mold at the right time.( It will merge with the rest of the mold to give you a bubble-free impression of your cockhead without this step you may get a bubble under the rim of your cockhead which will cause an unsightly lump on the finished clone. ![]() But if you're just ten seconds too late then it will fail completely - it won't take accept your cock once it starts to set.Ī tip for advanced cloners: after you mix the mold powder, apply a spoonful of it into the coronal ridge around your cockhead. If you put your cock in fifteen seconds too soon then you'll have to keep it firmly aroused an extra fifteen seconds while it sets up-an acceptable trade off. The molding powder (alginate) is extremely finicky and unforgiving. The procedure isn't very sexy, and it might even seem tedious, but that's exactly why you'll need to practice until you can do it instinctively with perfect timing while getting aroused at exactly the right moment. Really, seriously, practice it before trying it. I wish they'd come out with something that's premixed already or doesn't have temperature as a catalyst, it would be so much easier and less stressful.ĭo a practice run-through where you carry out all the instructions (stirring, measuring, timing, etc.) without actually mixing-in the molding powder.don't attempt to make an actual mold until you can get through a practice run with you cock fully aroused at exactly the right second to go into the mold. that makes me get too excited, and mixed with the mechanical act of the mold making process, too much to handle for me. Plus, the fantasies of doing myself with it, her doing herself with it, sucking it, etc. Its more the intimacy lost feeling from it all. All this made me lose way over 50% of my hard on, and the mold just didn't really do anything but fall in on itself as a result and I pulled out, again sad. The shit got really pushed out of the tube, all over my legs, floor, my foot, etc. I was losing it and threw the tube over me and felt myself get instantly soft from the cool/cold feel of the molding material. ![]() (it makes a mess on the floor if you're big, I found out this second go at it). I was hard, playing, was doing pretty good and she called me into the kitchen when it was just about time, was gonna pour it and hand it to me the second I got in there. Then she was mixing the next batch up a few days later. I actually came in her mouth while totally soft, it was a huge let down but not the cumming! All this distraction of doing regular things makes me loose my hard on, and this was the worst ever. I mean, an overly small flaccid, in my wife's mouth, when the minute before I was raging hard. First time I thought my wife would be able to give me head in the kitchen while I did the shit and did the waiting for water temperature to get right, and then mixing, and pouring, and then I was totally soft. I have had nothing but terrible results with these!!! Desperately wishing I could clone mine. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |